男人插女人骚视频,波多野结衣人妻厨房大战,亚洲国产精品成人精品无码区,亚洲 欧美 国产 综合首页

錘破制砂機供應廠家錘破制砂機錘破破碎機 

錘式破碎機的保養方法有哪些

1、定期檢查機器內部部件的磨損情況要定期檢查機器內部部件的磨損情況，如中心入料管、錐帽、葉輪上、下道襯板、圓周護板、鄂板的磨損程度，磨損較嚴重的要及時進行修補或更換，同時更換部件的重量、型號和尺寸等，一定都要按原來的部件參數進行更換。

2、做好潤滑工作要經常注意并及時做好摩擦面的潤滑工作，且所采用的潤滑脂應根據使用的地點、氣溫條件而定，一般情況下采用鈣基、鈉基和鈣鈉基潤滑脂;加入潤滑脂時應先用潔凈的或煤油清洗滾柱軸承的滾道，然后再加入，加入軸承座內的潤滑脂應為其空間容積的50%左右，錘破制砂機生產廠家，而且每3~6個月更換一次，這樣既確保了機器的正常運轉又延長了使用壽命。

3、保持設備的清潔要經常保持設備的清潔，做到無積灰、無油污、不漏油、不漏水、不漏電、不漏灰，更要注意灰塵等雜物不得進入潤滑系統和潤滑部位，錘破制砂機現貨銷售，因為這些雜物不僅會破壞潤滑油膜，而且會使設備失去潤滑而增加磨損，縮短設備的使用壽命;尤其要注意對軸承的定期清洗，破碎機在作2000小時后，打開主軸總成對軸承進行清洗，一般工作7200小時后要更換新軸承。

What are the maintenance methods for hammer crushers

1. Regularly inspect the wear of internal components of the machine, such as the wear degree of the central feeding tube, cone cap, impeller upper and lower channel lining plates, circumferential guard plates, and jaw plates. Those with severe wear should be repaired or replaced in a timely manner. At the same time, the weight, model, and size of the replaced components must be replaced according to the original component parameters.

2. Regular attention should be paid to and timely lubrication of the friction surface when performing lubrication work, and the lubricating grease used should be determined according to the location of use and temperature conditions. Generally, calcium based, sodium based, and calcium sodium based lubricating greases are used; When adding lubricating grease, the raceway of the roller bearing should be cleaned with clean or kerosene first, and then added. The lubricating grease added to the bearing seat should be about 50% of its spatial volume. The manufacturer of the hammer sand making machine should replace it every 3-6 months, which ensures the normal operation of the machine and extends its service life.

3. To keep the equipment clean, it is necessary to regularly maintain its cleanliness, ensuring that there is no accumulation of dust, oil, oil, water, electricity, or dust. It is also important to note that dust and other debris should not enter the lubrication system and lubrication parts. Hammer sand making machines are sold in stock because these debris not only damage the lubricating oil film, but also cause the equipment to lose lubrication and increase wear, shortening its service life; Special attention should be paid to regular cleaning of bearings. After 2000 hours of operation, the crusher should open the main shaft assembly to clean the bearings. Generally, new bearings should be replaced after 7200 hours of operation.