男人插女人骚视频,波多野结衣人妻厨房大战,亚洲国产精品成人精品无码区,亚洲 欧美 国产 综合首页

進口通風蝶閥認準德國洛克

進口通風蝶閥結構特點：

1.采用中線式碟板與短結構鋼板焊接的新型結構形式設計制造的，結構緊湊、重量輕、便于安裝、流阻小、流通量大，避免高溫膨脹的影響，操作輕便。

2.內無連桿、螺栓等、工作可靠、使用壽命長。可以多工位安裝，不受介質流向影響。

進口通風蝶閥規格參數： 

進口通風蝶閥產品簡介：

德國洛克《DE LOCKE》進口通風蝶閥采用與閥體相同材料加工成密封圈，其適用溫度隨閥體選材而定，公稱壓力≤0.6MP工，一般適用工業、冶金、環保等管道作通風調節介質流量之用。蝶閥的啟閉件是用圓形蝶板作啟閉件并隨閥桿轉動來開啟、關閉和調節流體通道的一種閥門。蝶閥的蝶板安裝于管道的直徑方向。在蝶閥閥體圓柱形通道內，圓盤形蝶板繞著軸線旋轉，旋轉角度為0°~90°之間，旋轉到90°時，閥門則牌全開狀態。

進口通風蝶閥安裝與維護：

1、安裝位置、高度、進出口方向必須符合設計要求，注意介質流動的方向應與閥體所標箭頭方向，連接應牢固緊密。

2、閥門安裝前必須進行外觀檢查，閥門的銘牌應符合現行國家標準《通用閥門標志》GB 12220的規定。對于工作壓力大于1.0 MPa 及在主干管上起到切斷作用的閥門，安裝前應進行強度和嚴密性能試驗，合格后方準使用。強度試驗時，試驗壓力為公稱壓力的1.5倍，持續時間不少于5min，閥門殼體、填料應無滲漏為合格。嚴密性試驗時，試驗壓力為公稱壓力的1.1倍；試驗持續的時間符合GB 50243要求。

1. The installation position, height, inlet and outlet direction must meet the design requirements. Pay attention to the direction of medium flow and the arrow direction marked on the valve body, and the connection should be firm and tight.

2. The valve must be visually inspected before installation, and the valve name plate shall comply with the provisions of the current national standard "general valve marks" GB 12220. For the valve with working pressure greater than 1.0 MPa and cut-off function on the main pipe, the strength and tightness test shall be conducted before installation, and the valve can only be used after it is qualified. During the strength test, the test pressure shall be 1.5 times of the nominal pressure, the duration shall not be less than 5min, and the valve shell and packing shall be qualified if there is no leakage. During the tightness test, the test pressure is 1.1 times of the nominal pressure, and the test duration meets the requirements of GB 50243.