圓形化糞池模具 圓形臥式化糞池模具 可按要求定制
圓形化糞池模具 圓形臥式化糞池模具 可按要求定制
圓形化糞池模具 圓形臥式化糞池模具 可按要求定制
圓形化糞池模具 圓形臥式化糞池模具 可按要求定制
圓形化糞池模具 圓形臥式化糞池模具 可按要求定制
圓形化糞池模具 圓形臥式化糞池模具 可按要求定制
圓形化糞池模具 圓形臥式化糞池模具 可按要求定制

圓形化糞池模具-圓形臥式化糞池模具-可按要求定制

價格

訂貨量(套)

¥16500.00

≥5

聯系人 邊進輝 經理

掃一掃添加商家

잵잰잰잰잰잭잭잰잭잵잭

發貨地 河北省保定市
進入商鋪
掃碼查看

掃碼查看

手機掃碼 快速查看

在線客服

商品參數
|
商品介紹
|
聯系方式
加工定制
貨號 化糞池模具
類型 焊接成型
品牌 樂豐模具
型號 多種型號
適用范圍 道路工程
產品別名 圓形化糞池模具
材質 鋼板
模具產地 河北
質量體系 ISO9001
商品介紹

圓形化糞池模具 圓形臥式化糞池模具 可按要求定制


化糞池模具深受市場的廣大好評,而化糞池模具這幾年一直使用的是立式三格化糞池模具,有的工程難以滿足需要,所以臥式化糞池模具登上了市場舞臺,這里簡短的介紹一下。化糞池模具屬于大型鋼模具,從三格化糞池的使用到臥式化糞池的推廣,是市場競爭以及市場需要的結果,更多的化糞池模具介紹由保定利昌模具廠發布。化糞池鋼模具采用的鋼板多達6個厚,筋板也是8個厚的,這樣的厚度是為了保證模具的不變形,壁厚15公分的設置很好的滿足了生產的需要,一套模具大概重量在3.3噸左右。


一般情況下,農村自建房的化糞池大小以長2.7米,寬1.5米,深度為1.3米為宜。用的較多的結構一般為目字形結構,如圖所示:


三個池子的容積比一般為2:1:3,在寬度和深度一樣的情況下,也就是說一池,二池,三池的長度比應該為2:1:3如圖所示:


一池和二池之間用過糞管連接,過糞管采用長度為70-75cm,內徑為15cm的PVC管,過糞管與隔墻的夾角以60度為宜。


二池和三池之間也用過糞管連接,過糞管采用長度為50-55cm,內徑為15cm的PVC管,過糞管與隔墻的夾角以60度為宜。


The septic tank mold is well received by the market. In recent years, the vertical three grid septic tank mold has been used. Some projects are difficult to meet the needs, so the horizontal septic tank mold has stepped onto the market stage. Here is a brief introduction. Septic tank mold belongs to large steel mold. From the use of three grid septic tank to the promotion of horizontal septic tank, it is the result of market competition and market demand. More septic tank mold introduction is issued by Baoding Lichang mold factory. The septic tank steel mold uses up to 6 thick steel plates, and the rib plate is also 8 thick. This thickness is to ensure that the mold does not deform. The setting of the wall thickness of 15 cm meets the production needs well. A set of mold is about 3.3 tons in weight.


In general, the size of the septic tank for self built houses in rural areas should be 2.7m long, 1.5m wide and 1.3m deep. The most commonly used structures are eye shaped structures, as shown in the figure:



The volume ratio of three pools is generally 2:1:3. In the case of the same width and depth, that is to say, the length ratio of one pool, two pools and three pools should be 2:1:3, as shown in the figure:



The first tank and the second tank are connected by a waste pipe. The waste pipe is a PVC pipe with a length of 70-75cm and an inner diameter of 15cm. The angle between the waste pipe and the partition wall should be 60 degrees.



The second tank and the third tank are also connected by the fecal pipe. The length of the pipe is 50-55cm and the inner diameter is 15cm. The angle between the pipe and the partition wall is 60 degrees.



聯系方式
公司名稱 保定市清苑區樂豐模盒模具加工廠
聯系賣家 邊進輝 (QQ:873416854)
電話 잵잰잰잰잰잭잭잰잭잵잭
手機 잵잰잰잰잰잭잭잰잭잵잭
傳真 재잰잵잭-잳잱잴잭잰잴잰
地址 河北省保定市
聯系二維碼